Induction Bend Pipe is a process when the heat is used on a particular area of a metal section- pipe or tube, to allow it to bend easily. The heat is applied using an induction coil heated to a preset temperature to give the metal a bend of a preset radius. The process is also often referred to as hot pipe bend.
The temperature of the coil ranges from 800-2,200 degrees depending on the type of metal, its grade, temper, and thickness of the section. The process involves applying pressure on the metal while the coil is hot thereby allowing for easy bending. Once the desired radius of the bend is achieved, the section is cooled with water or air spray. The benefits of Induction Bend Pipe: There are several advantages of bending metal pipes using this technique: Since the process involves heating a particular area of the pipe, it ensures that the distortion on the section is minimal once the bending process is completed. The amount of energy required to carry out the process is minimum, the process results in systems that have higher energy efficiency. Induction Bend Pipe does not require internal mandrels and sand filling, thereby saving on cost. The process does not take very long compared to the other metal bending techniques, thereby adding to its cost-efficiency. The need for welded or mechanical joints is eliminated by this method which means that there is no need for the surfaces for a neat finish. The applications of Induction Bend Pipe: The process of bending can be used for nearly any metal and even alloys such as steel and all kinds of pipe sections. In typical cases, this metal bending technique is used on massive pipes like petroleum pipelines. However, its use also extends to smaller pipe sections such as farming tools and springs. Induction Bend Pipe is often confused with hot rolling. The latter is quite different and it involves changing the thickness and shape of the metal after heating it to a required temperature called the critical temperature. The technique is generally used for metal sheets where the entire sheet is heated and then rolled to the desired radius. Its applications are limited because of it of its relatively lower cost-effectiveness and energy efficiency. The sections thus produced are generally used as feed for rolling mills or directly for fabrication. WeatherockGroup worldwide is one of the world's top manufacturers & Supplier of top-quality Double Submerged arc welded (DSAW) Pipe and Longitudinal Welded Pipe. Our high-performance products include Induction Bend Pipe Manufacturers Read More: - https://www.articleted.com/article/328716/16416/What-is-Induction-Bend-Pipe-Manufacturers
0 Comments
Sucker rods are long metallic pipes and threaded at both ends. These are used in the process of the oil industry to join together the surface and downhole components of a reciprocating piston pump installed in an oil well. The WEATHEROCK GROUP provides sucker rods for petroleum and other industrial sectors. Fiberglass sucker rods are stronger, lighter, and more elastic than steel sucker rods, reducing stresses on the rod string while allowing for more fluid production and lower lifting costs. But the steel sucker rods are stronger and durable.
The WEATHEROCK GROUP is one of the best Sucker Rods Manufacturers. The various uses of sucker rods are Casing & Coupling, Jet Mud Mixer, Air Blower Parts, Degasser, Safety Clamp, Oil & Gas Separator, Shale Shaker Screen, Mud Agitator, Pup Joint, Mud Tank, Kelly, generator set spares, Hydraulic Hose, slips, BOP, Hydraulic Filter, Casing Centralizer, Air Winch, Hammer Union, Boiler Centrifugal Fans etc. Sucker rod beam pumping provides mechanical energy to lift oil from bottom hole to surface. It is efficient, simple, and easy for field people to operate, and it can pump a well down to very low pressure to maximize oil production rate. It is applicable to slim holes, multiple completions, and high-temperature and viscous oils. The system is also easy to change to other wells with minimum cost. Sucker Rods Manufacturers refers to the WEATHEROCK GROUP due to their quality materials and service which are last for a long time and also more durable. They are providing Safety, Quality, and Performance Driven product to all their clients. Through many years of developments, Today WEATHEROCK GROUP is one of the world’s conglomerate groups and plays a very important role in the energy business field. Their business is involved in manufacturing, service & solutions and investments etc. They believe in customer satisfaction. Looking for Sucker Rod Manufacturers & Pony Rod Manufacturers In worldwide? Contact weatherockgroup.com we providing the best & high-quality Sucker Rods Manufacturers and Pony Rod Manufacturers by verified and qualified manufacturers. Article Source - https://www.articleted.com/article/323727/16416/Sucker-Rods-Manufacturers |